.11.848.221.407 G2007Y For Kjellberg Plasma Cutter Machine Nozzle
We can offer you all plasma consumables for hyptertherm, Kjellberg,
Esab, Koike, Komatsu, Thermadyne, such as: electrode, nozzle,
shield, swirl ring, inner cap, retaining cap, water tube, torch
body and so on.
If you worry about our products’ quality, I can give you some
samples to test by free. Please don't hesitate to contact us if you
have any questions or concerns before or after your purchase. We
are committed to your 100% satisfaction.
Shipping and handing
1. DHL is our preferred shipping method. Meanwhile TNT, EMS, Fedex,
UPS are available.
2. Make sure to leave telephone number when filling your buyer
3.You can check the goods where it is in transit through tracking
1.If you are not satisfied with your purchase, you can echange the
items received. you must contact us within 5 days of the receipt
of your order. And you should pay all additional shipping fees
incurred and the items returned should be kept in their original
2.If you wish to echange defective or incorrect shipped goods,
please contact us within 5 days after receiving the goods.
1. The buyer are responsible for any insurance you think necessary.
2. The processing time for a specific order varies with the product
type and stock status. Mostly, processing time can be 3 to 15
|Machine||HEC NO.||Thum NO.||Ref NO.||Description|
|K1466||G2006||.11.848.221.406||Nozzle O2 25A|
|K1467||G2007||.11.848.221.407||Nozzle O2 35A|
|K641515||G4015||.11.848.201.1515||Swirl gas cap|
|K641220||G4020||.11.848.201.1520||Swirl gas cap|
|K1468||G2008Y||.11.848.221.408||Nozzle O2 50A|
|K14610||G2010Y||.11.848.221.410||Nozzle O2 80A|
|K14612||G2012Y||.11.848.221.412||Nozzle O2 120A|
|K14614||G2014Y||.11.848.221.414||Nozzle O2 160A|
|K14616||G2016Y||.11.848.221.416||Nozzle O2 200A|
|K641522||G4022||.11.848.201.1522||Swirl gas cap|
|K641525||G4025||.11.848.201.1525||Swirl gas cap|
|K641530||G4030||.11.848.201.1530||Swirl gas cap|
|K14826||G2326Y||.11.848.421.426||Nozzle O2 280A|
|K14830||G2330Y||.11.848.421.430||Nozzle O2 360A|
|K641745||G4345||.11.848.401.1545||Swirl gas cap|
|K641750||G4350||.11.848.401.1550||Swirl gas cap|
|K641755||G4355||.11.848.401.1555||Swirl gas cap|
Anti interference wiring measures for machine tools
CNC device and servo unit of NC plasma arc cutting system is the
core part of the system, the power supply is the main way to enter
the interference. The interference of power supply is mainly
produced by the impedance coupling power supply line, all kinds of
high-power electric equipment is the main source of interference.
3.1 power supply into line with shielded wire
Power line NC plasma arc cutting system. Cathode line of the
cutting torch and plasma / arc arc line hanging in the sliding
support, equivalent to go parallel lines tens of meters and / arc
line control, torch cathode line from the plasma power, torch
cathode of the DC line current 100 amperes. It produces
electromagnetic field and high frequency lead arc of high frequency
signal by coupling the will power of CNC device and servo unit
caused by electromagnetic interference.
With copper and aluminum for shielding cable shielding layer can
effectively suppress the interference of high frequency
electromagnetic shielding, grounding can inhibit the change of the
field of electrostatic induction core wire.
The use of 3.2 power filter
Power filter is an indispensable component in the anti
interference, high frequency and low frequency section has good
interference suppression performance. Use should pay attention to
A) filter should be installed on the surface of the conductive
metal, or woven through the ground and ground;
B) location filter should be as close as possible to the power line
at the entrance;
C) filter input and output the best use of shielded wire or twisted
D) to avoid the input and output lines of mutual coupling, the
absolute prohibition of the input and output lines bundled with the
use of shielded wire.