Kjellberg PA-S70W Cathode .12.4087 K2 Electrode For Kjellberg
Electrode: M002, M012, M001, M011, S002Y, S012X, T012Y, S042, S052,
G002Y, G032Y, G092Y, G015Y, G071, G052, G042 and so on.
Nozzle: M2006, M2007, M2008, M2009, M2010, M2112, R2007, R2008,
R2009, R2010, R2011, R2012, S2006X, S2007X, S2008X, S2009X, S2010X,
S2011X, S2012X, S2014X, S2016X, S2514X, S2516X, S2518X, S012X,
S2112X, S2114X, S2116X, T2115, T2120, T2125, T2127, T2130, T2523,
T2525, T2427, T2429, G2006Y, G2207Y, G2008Y, G2009Y, G2010Y,
G2011Y, G2012Y, G2014Y, G2016Y, G2326Y, G2330Y, G2331Y, G2514Y,
G2516Y, G2518Y, G2725Y, G2727Y, G2729Y.
Swirl gas cap: V4335, V4330, V4340, V4345, V4350, V4360, V4535,
V4540, V4550, V4560, Z4015, Z4020, Z4022, Z4025, Z4030, Z4140,
Z4530, Z4535, Z4545, Z4540, R4020, R4022, R4025, R4130, R4140,
R4525, R4530, R4540, G4020, G4022, G4025, G4030, G4035, G4040,
G4330, G4335, G4340, G4345, G4350, G4355
Nozzle cap: M3004, M3008, M3028, S3004, S3008, S3018, S3028, T3000,
T3030, T3045, T3145, T3060, T3160, T3208, T3209, T3219, T3228,
R3004, R3008, R3018, R3028, G3004, G3018, G3028
Protection Cap: Z501, T502, T503, V502, T522, G3209, G3219, G3249
Gas guide: Z101, Z102, Z111, Z111A, G101, G102, G121, G125
Water Tube: T901, V931, PB-S75, PB-S46/47, .11.842.601.152, G931
|Machine||HEC NO.||Thum NO.||Ref NO.||Description|
|1||K720310||R012||11.842.721.310||O2 XL R012 (3D)|
|3||K730162||R3008||11.842.601.162||0.8 R3008 (3D)|
|15|| || ||.10.505.908||O-ring 18.2 X 1.9 VMQ ISO 1629 70SHSW|
|16|| || ||.10.505.923||O-ring 28 X 2.0 VMQ ISO 1629 70 shore|
Maintenance of plasma cutting machine
1. correct assembly torch
Right, carefully install the torch, ensure all parts with good, to
ensure that the gas and the cooling air. Install all of the
components on a clean cloth, avoid dirt stuck to components. In the
O ring on the appropriate lubrication oil, O ring to change light
as the standard, can not be more.
2. consumption of parts in a timely manner before the complete
Consumption with completely damaged parts do not change, again
because of severe wear of electrode, the nozzle and the vortex ring
will have control of the plasma arc, extremely easy to cause the
torch of serious damage. So when the first cut in the quality of
the cut, it should be timely check the consumption.
3. The connecting thread cleaning torch
In the replacement of expendable thing or daily maintenance
inspection, must assure cutting torch, within the thread clean and,
if necessary, should be clean or repair connection thread.
4. the contact surface of the cleaning electrode and nozzle
In a lot of cutting torch, the contact surface of the nozzle and
the electrode is charged the contact surface, if the contact
surface with dirt, cut the torch can not work normally should be
using hydrogen peroxide cleaning cleaning agent.
5. check the gas and cooling gas every day
Check the flow and pressure of the gas and cooling gas flow every
day, if the flow is not enough or there is leakage, should stop the
line fault immediately.
6. avoid torch collision damage
In order to avoid collision damage to torch should be correctly
programming avoid walking overrun system, install anti-collision
device can effectively avoid the collision torch damage.
7. The damage reason of the most common torch
(1) the torch collision.
(2) the destructive plasma arc due to the damage of the consumable
(3) dirt caused by the destructive plasma arc.
(4) loose parts caused by destructive plasma arc.
8. matters needing attention
(1) do not grease the cutting torch.
(2) don't over use O - ring lubricant.
(3) in protection to remain on the cutting torch when splash do not
(4) do not take manual torch when use hammer.